Categories
Home Improvement

Another Best Tips to Fix Shower Leaks for Home Improvement

Many home remodeling projects require you to err on the side of caution. Shower projects require a whole new level of care to ensure that you don’t run into serious and costly problems. Shower leaks under floors or behind walls can lead to serious problems that require professional help to remedy and cost a lot such as insect invasion, mold growth, and flooding.

You should seriously consider consulting an expert to remodel a shower unless you are familiar with working under strict conditions and are comfortable with doing plumbing work. In most cases, it makes more sense to hire someone with experience to specifically fix shower and bath leaks.

Once the old shower has been removed you need to remove as much of the old glue or caulk as you can to ensure a flat surface for the new shower to fit against snug and evenly. Begin with making sure the pipe for the drain is clean and smooth for at least one inch from the end.

Sand away any rust or calcium buildups and if the pipe is corroded replace it with a new one. If you require a pipe replacement you should stop working and call a professional as this is a delicate job that requires that it be done properly.

When attaching pipes of two different materials, namely copper and galvanized pipes, be sure to use an insulating material at the joint to prevent an electrochemical reaction that can cause the pipes to corrode. Also, be sure to wrap threaded joints with a generous wind of Teflon plumbers tape.

Once your surfaces are carefully prepared you can lower the unit into place being sure to lay a bead of caulk around the base of the unit follow the manufacturer’s installation instructions and seal the resulting joints with silicone caulk. Pay careful attention to placing the unit and components at the proper angles to provide for proper drainage, positioning, and fit.

Once the unit and joints have had a few hours to dry test for leaks use some material to plug the area around the flange then flood the area with water and check for leaks. Once you have fixed any leaks you can install the shower door’s hardware components.

When drilling for fasteners be sure to follow instructions that came with the unit and seal the exterior surfaces. You should not seal interior surfaces as you want that moisture to drain back into the tub. This will cut down on the buildup of mold and mildew as well as help prevent the warping of the tracks the door lies in.

Categories
Home Improvement

The Best Lighting Options for Your Home Improvement

Selecting lighting options for your home these days can be overwhelming as there are more choices and varieties than one can imagine. You can find lights to achieve any look that your imagination can dream up.

If you have an older home your options may be slightly limited as the wiring may be old and not be quite as sophisticated as wiring in newer homes. Getting familiar with the quality of your home’s wiring as well as with local electrical codes will help you tremendously when shopping for lighting.

For older homes, it’s recommended to have a contractor come out for a consultation to help you decide if you should replace an older wiring system. Find out what your existing electrical system can handle capacity-wise prior to making lighting decisions. You may also be able to save on electrical costs over time by installing a new and more energy-efficient system.

Modern compact fluorescent lights can produce a somewhat natural light with up to 30% efficiency increases over incandescent bulbs. These compact lights come in a ton of wattages, sizes, shapes, and colors.

The latest in the light design are LED lamps. These lights are made from arrays of tiny light-emitting diodes. LED lighting solutions are usually quite expensive but produce far less heat, last a tremendously long time, and will provide huge savings in electric costs. Some LED lamps are rated to last 35 years, with more common lifetimes coming in around 6-7 years.

If you have a penchant for high-tech you may wish to consider concrete with embedded fiber optic fibers. These blocks provide a unique look when backlit, providing various colors and effects.

When designing an effective lighting system you need to consider what room you are designing for and your specific lighting needs. Bathrooms generally are brighter than bedrooms to be suitable for shaving and makeup application. Living rooms often have a more dynamic lighting profile including both intense and soft lighting.

Objects appear the way that they do in part due to what have called lighting temperature. This measurement, in Kelvin units, is used to measure how close lights are to natural sunlight. Lights that appear artificial and unnatural often have lower “color temperatures”.

A northern sky in clear conditions near noontime will be somewhere around 7,000 to 8,000 Kelvins; the average florescent bulb weighs in at 4,000 Kelvins, while a regular old incandescent at about 2,800 Kelvins.

More modern light types will give you an appearance closer to that of natural light. Keep this in mind when deciding which type of lamps to purchase. If you wish for a softer lighting scheme consider recessed lighting options or lights that have lower color temperatures.

Categories
Home Improvement

You Should Know All About the Insulating a Ceiling for Your Home Improvement

Insulating ceilings is like putting a thick blanket over each room. It seals the warmth in and keeps the cold out. It cuts heat loss by as much as 50 percent while the cost is minimal. For an average home should cover all of the necessary expenses in properly insulating your ceiling varying by coverage area.

This is not an expensive home improvement project if you keep in mind that you could well achieve a 30 percent savings to your winter heating bills. In addition, your home will normally stay cooler during summer months as well, by retaining the cool air from your air conditioner within the room.

Tools and Materials

Simply calculate the total ceiling surface area (width x length). In addition, measure the distance between floor/ceiling joists. Insulation is sold in varying widths depending on their application so being prepared will help prevent multiple trips to your home improvement retailer. Your insulation supplier can calculate the number of bats required for the job and the proper size of the individual bats.

Also, consider the reasons you wish to insulate. It isn’t always to cut heating and cooling costs. You might also want to dampen sound from carrying through the home. If you are insulating a room when finishing a basement and that basement is primarily used for watching movies and shooting pool, you may wish to use insulation rated to also deter sound.

With the bats, a ladder, leadlight, a trimming knife (for cutting the bats to size), gloves, particle mask, long-sleeved shirt and long trousers (the insulation can irritate your skin and nasal passages), and two pieces of meter square 18 mm ply or particleboard for cutting and kneeling on, you’re ready to go.

For upstairs rooms, meaning you are visiting your attic to install the insulation, use planks that span at least four of the chords to spread your weight evenly across.

Steps to Insulate Your Ceiling

Choose a cool day (especially if installing in the attic) and begin packing the bats tightly between the joists, making sure you reach right to the external wall plate. Work back toward the access hole. Leave no spaces for maximum effect.

Again, for attic installation, remember to always keep your weight on the joists and not the ceiling itself, the drywall will not be able to support you! The recommended plank or plywood square will make the process more comfortable.

If installing under the roof itself, use a 75 mm slat of wood that just fits between the joists and affix it to the end of a broom handle. That will provide a useful push-in tool for moving the bats into awkward places.

Be especially careful around any wiring

When necessary cut around things like ceiling fan electrical connections some have suggested using a stiff cardboard separator between the insulation material and the wiring, but if you can, simply tuck the insulation further in behind the wiring.

In most cases, the wiring has been stapled close to the end of the joist so there is often enough room to install the bat behind the wiring so that the paper side is still tucked behind the wiring and does not come into contact at all.

Most pre-batted insulations have folds of paper running along both sides that allow for flaps to be folded against the joists and stapled. Take the time to do this. It provides a cleaner installation and prevents any need for worry that at some time in the future the insulation may be resting on wires, etc.

You are now snug in your home during winter and summers should be cooler, too.

Categories
Home Improvement

You Can Home Improvement With Kitchen Cabinet Installation

Installing kitchen cabinets is a project that most do-it-yourselfers can handle without a problem for home improvement. If you have some basic skills and care the results obtained by doing it yourself can be just as good as if a professional did it; and save you money to boot.

A key to installing cabinets is making sure that they are level. If you don’t have two or three people available to hold the cabinets and help you install them you can use a support or a jack.

You can build a simple T-shaped brace from wood, place it under the cabinet, and then insert the jack underneath of the cabinet. You can also use specialized support systems made for installing cabinets. Be sure to use multiple supports to make sure that the cabinets don’t wobble.

If the bottom cabinets are already installed you can use metal stain buckets and phone books on top of them to position the top cabinets? This works in a pinch but jacks made for installing cabinets would obviously be the ideal solution.

Once you have the cabinets positioned you will have to locate the studs in the wall that you will be attaching the cabinets to. Never attempt to attach cabinets to the drywall by itself. The studs located in the walls of most homes’ inner walls will be placed sixteen inches apart.

To locate them you can use the sixteen-inch guideline as a starting point and then use an electronic stud location device to find their exact positions within the wall. You should be attempting to locate the center of each stud as this is the ideal location to drive the fastener into.

To make this easier you can draw the locations of the stud centers onto the wall and then pre-drill the holes for the fasteners using a bit slightly smaller than the screw itself. You also will need to drive any holes for wiring before installing the cabinet units themselves.

You should double-check your measurements by making them both on the wall and on the actual cabinets. You should try to provide for eighteen inches of clearance between the cabinets and the countertops.

For a more secure cabinet, you should drill and fasten the unit through the trim or supports rather than through the back wall which is often thin. This may not be possible for the cabinets that you choose but if you can do it this way it’s much better. Also, be sure to use three-inch screws for the major support fasteners that hold the cabinets to the wall.

If you wish to add additional support to your cabinets you can take a one-inch thick strip of wood that is 2 inches tall and screw it into the wall where a stud exists. It’s possible to attach the support strips first but if you need to tweak the cabinet position and this could present a problem.

Categories
Home Improvement

Doing Up Your Spare Room for Home Improvement

If you’ve decided to finally get started on that project to do up your spare room for home improvement, a call to your home contents cover provider is unlikely to be high on your list of priorities. With exciting things like color schemes, new furniture, and the ambiance of the room to think about, the comparatively dull world of insurance could seriously dent your creative mojo.

However, avoid making that call to your contents insurer at your peril; if you’re spending a quid or two on the job, you’ll want to make sure everything is covered, especially considering the number of accidents we Brits have when carrying out a spot of DIY. According to the Royal Society for the Prevention of Accidents, a staggering 600 people go to the hospital every day after suffering a DIY mishap.

Every year 20,000 Brits are injured while using scalpels and knives during their home improvement projects, while an eye-watering 15,000 suffer an injury while using a saw. More painful still, 2,000 ends up in A&E after a sticky situation with an ax, plane, or welding equipment.

Scary statistics, but there’s a real message behind the numbers: accidents can and do happen and it’s best to be prepared. Before you start a project, this could include making sure that you have adequate home insurance, including accidental damage cover.

Although it’s nice to think of a project going as smoothly as possible, it’s not hard to imagine the things that can go wrong, whether it’s spilled paint pots, broken furniture, or collapsed ceilings. Smash into the wrong wall or pull up the wrong floorboard and you could even be looking at structural damage.

So you’ve completed the project and everything’s gone smoothly, you’re out of the woods, right? Sadly not. Once you’ve finished creating your exciting new space, you may also need to put a call into your insurance provider again – this time to let them know of your changes. The cost of new furniture can mount up, especially if you’ve let your imagination run away with you and invested in some opulent pieces to complete your new room.

The easiest way to get the best value out of your home contents insurance is to regularly review exactly what’s in your home, how much it would cost to replace and get it covered. Pay for too much cover and you’re wasting money, cover too little and the results could be disastrous – find the right balance and you’ll be well on the road to a harmonious home.